Inlet (Water Overlay): Difference between revisions

From Tygron Support wiki
Jump to navigation Jump to search
No edit summary
No edit summary
 
(24 intermediate revisions by 4 users not shown)
Line 1: Line 1:
Inlets are points where water is either added to or removed from the hydrological model. It will add or remove water at a defined maximum rate, with optional thresholds for the amount of water to add or remove.
{{Inlets}} are hydraulic structures that can pump water in to the hydrological model, or out of, in which case they function as '''Outlets'''. It will add or remove water at a defined maximum rate, with optional thresholds for the amount of water to add or remove.


[[File:waterwizard_icon_inlet.png]] An inlet is a [[Point-based_construction_(Water_Overlay)|point-based construction]].
[[File:waterwizard_icon_inlet.png|75px]] An {{Inlet}} is by default a [[Point-based_building_(Water_Overlay)|point-based building]], but can optionally be an [[Area-based_building_(Water_Overlay)|area-based building]].
{{Overlay attribute
 
|attribute=[[Inlet_q_(Water_Overlay)|INLET_Q]]
{{Overlay keys|suppresscategory=true|
|unit=m3/sec
{{:inlet q (Water Overlay)}}
|description=The maximum amount of water flowing into the model through this inlet. A negative value means the construction functions as an outlet, and water is removed from the hydrological model.
{{:inlet area (Water Overlay)}}
|defaultvalue=0
{{:inlet capacity (Water Overlay)}}
|icon=[[File:waterwizard_icon_inlet_q.png]]
{{:inlet lower threshold (Water Overlay)}}
|attribute2=[[Lower_threshold_(Water_Overlay)|LOWER_THRESHOLD]]
{{:inlet upper threshold (Water Overlay)}}
|unit2={{mdatum}}
{{:inlet underground (Water Overlay)}}
|description2=If a lower threshold is set, water will only flow into the model through this inlet until the water level at the point of this inlet is equal to or greater than the threshold. If the threshold is not set, the amount of water flowing in is not limited in this fashion.
|defaultvalue2=None
|icon2=[[File:waterwizard_icon_lower_threshold.png]]
|attribute3=[[Upper_threshold_(Water_Overlay)|UPPER_THRESHOLD]]
|unit3={{mdatum}}
|description3=If an upper threshold is set, water will only flow out of the model through this outlet until the water level at the point of this inlet is equal to or lower than the threshold. If the threshold is not set, the amount of water flowing out is not limited in this fashion.
|defaultvalue3=None
|icon3=[[File:waterwizard_icon_upper_threshold.png]]
|attribute4=[[Inlet_capacity_(Water_Overlay)|INLET_CAPACITY]]
|unit4=m3
|description4=The maximum amount of water which can flow in or out through this construction. Water flowing back in the other direction replenishes the capacity.
|defaultvalue4=0
|icon4=[[File:waterwizard_icon_inlet_capacity.png]]
}}
}}
==Notes==
 
* Each Inlet attribute functions as a limit to the flow. If multiple are defined, the flow is limited by the strongest limit. If neither an [[Inlet_q_(Water_Overlay)|INLET_Q]] or any threshold is defined, there will be no flow.
{{article end
* A negative [[Inlet q (Water Overlay)|INLET_Q]] changes the Inlet to an Outlet.
|notes=
* The [[Lower threshold (Water Overlay)|lower]] and [[Upper threshold (Water Overlay)|upper threshold]]s can be seen as a the lowest and highest of "range" of valid water levels. If the actual water level does not fall in the specified range, the inlet will allow water to flow in or out (depending on the configuration) to correct the water level.
* Most {{Inlet}} attributes function as a limit to the flow. If multiple are defined, the flow is limited by the strongest limit. If neither an [[Inlet_q_(Water_Overlay)|INLET_Q]] or any threshold is defined, there will be no flow.
==See also==
* A negative [[Inlet q (Water Overlay)|INLET_Q]] changes the {{Inlet}} to an {{Outlet}}.
* [[Inlet_formula_(Water_Overlay)|Inlet formula]]
* The [[Pump lower threshold (Water Overlay)|lower]] and [[Pump upper threshold (Water Overlay)|upper threshold]]s can be seen as a the lowest and highest of "range" of valid water levels. If the actual water level does not fall in the specified range, the {{Inlet}} will allow water to flow in or out (depending on the configuration) to correct the water level.
* A [[Pump (Water Overlay)|Pump]] is different from an [[Inlet (Water Overlay)|{{inlet}}]] in that a pump has two endpoints (or areas) within the project areas, whereas an {{inlet}} has an end point (or area) within the project area and an endpoint (or area) outside the project area; a conceptual external area with a size and a water level.
|howtos=
* [[How to correct inlets on land]]
* [[How to correct multiple buildings on the same location]]
|seealso=
* [[Inlet formula (Water Overlay)]]
 
}}
 
{{WaterOverlay hydraulic structure nav}}
{{WaterOverlay hydraulic structure nav}}
{{Water Module buttons}}

Latest revision as of 09:41, 29 January 2024

Inlets are hydraulic structures that can pump water in to the hydrological model, or out of, in which case they function as Outlets. It will add or remove water at a defined maximum rate, with optional thresholds for the amount of water to add or remove.

Waterwizard icon inlet.png An Inlet is by default a point-based building, but can optionally be an area-based building.

Notes

  • Most Inlet attributes function as a limit to the flow. If multiple are defined, the flow is limited by the strongest limit. If neither an INLET_Q or any threshold is defined, there will be no flow.
  • A negative INLET_Q changes the Inlet to an Outlet.
  • The lower and upper thresholds can be seen as a the lowest and highest of "range" of valid water levels. If the actual water level does not fall in the specified range, the Inlet will allow water to flow in or out (depending on the configuration) to correct the water level.
  • A Pump is different from an Inlet in that a pump has two endpoints (or areas) within the project areas, whereas an Inlet has an end point (or area) within the project area and an endpoint (or area) outside the project area; a conceptual external area with a size and a water level.

How-to's

See also