Weir height test case (Water Module): Difference between revisions

Latest revision as of 12:53, 3 February 2023

This page contains information on what ways a weir's height can be configured using a test case. It also shows what direct output you can inspect from a weir. Finally, several variants are also explored.

Description

This test case consists of several weirs situated in a waterway, with each weir having different properties. All weirs are part of the same Water Overlay's simulation. There is no rainfall in this test case. Instead water flow is provided by inlets and outlets, which can be set up either variable or constant.

Weir test case top down.

Boundary and initial conditions

Waterways with weirs in the middle, separating two water areas.
One inlet per waterway providing an influx of water, situated in the water area on the left.
One outlet per waterway providing an outflux of water, situated in the water area on the right.

Parameter values

Manning’s n: 0.03 (uniform)
Model grid resolution: 1m

Technical setup

Waterways

Four waterways with a water depth of 2m and an angle of repose of 35 degrees, drawn with the following polygons:

[187.0, -249.288], [418.0, -256.288]
[413.0, -333.288], [189.0, -326.288]
[194.0, -375.287], [411.0, -382.287]
[404.0, -447.430], [194.0, -440.430]

Water Areas

Two areas divide the water ways into two sections:

Water area (left)
- Rectangle shape: [301.0, -226.466], [158.884, -464.466]
- WATER_LEVEL = 0.0;
Water area (right)
- Rectangle shape: [424.884, -226.466], [301.0, -464.466]
- WATER_LEVEL = 0.0;

Inlets

Inlet (Constant):
- Rectangle shape: [189.82, -254.350], [202.08, -251.510]
- INLET_AREA = 1.0;
- INLET_Q = 1.0;
- LOWER_THRESHOLD = -10 000 (inactive);
- UPPER_THRESHOLD = -10 000 (inactive);

Inlet (Manual)
- Rectangle shape: [192.116, -331.225], [199.453, -328.390]
- INLET_AREA = 1.0;
- INLET_Q = 1.0;
- LOWER_THRESHOLD = -10 000 (inactive);
- UPPER_THRESHOLD = -10 000 (inactive);

Inlet (Adjusting)

Inlet Q that is adjusting over time, visualized using the Measurement Tool's object attribute inspection.

- Rectangle shape: [197.019, -444.276], [204.623, -441.738]
- INLET_AREA = 1.0;
- INLET_Q = [0, 1, 600, 1, 900, 1.5, 1200, 1.5, 1800, 1.5, 2400, 1, 3600, 1];
- LOWER_THRESHOLD = -10 000 (inactive);
- UPPER_THRESHOLD = -10 000 (inactive);

Outlets

Each outlet is set up with the following attributes to remove the water that passed through the weir:

- INLET_AREA = 1.0;
- INLET_Q = 0;
- UPPER_THRESHOLD = -0.5;

The outlets are situated at:

Outlet (Constant):
- Rectangle shape: [414.554, -250.689] , [396.786, -253.873]
Outlet (Manual):
- Rectangle shape: [410.115, -327.753] , [ 393.13, -330.9620 ]
Outlet (Adjusting):
- Rectangle shape: [ 401.072, -442.541 ], [ 383.968, -445.520 ]

Weirs

Each weir is setup using a rectangular shape, and direction angle and a weir height and width:

WEIR_ANGLE = 270 degrees;
WEIR_HEIGHT = 0 m;
WEIR_WIDTH = 5 m;

Weir specific:

Weir (Constant)
- Rectangular shape: [ 299.593, -248.328 ] , [ 302.229, -257.983 ]
Weir (Manual)

Weir height that is adjusting over time, visualized using the Measurement Tool's object attribute inspection.

- Rectangular shape: [ 298.675, -324.174 ] , [ 301.613, -335.662 ]
- WEIR_HEIGHT = [ 0 0 600 0.2 1200 0.2 1500 0.2 1800 -0.5 2400 -0.5 2700 0 ];
Weir (Adjusting)
- Rectangular shape: [ 298.406, -437.681 ] , [ 301.142, -449.731 ]
- WEIR_TARGET_LEVEL = 0;

Overlay settings

General parameters that have been used:

Type of overlay: Rainfall Overlay
Weather:
- Evaporation: 0 mm
- Rain: 0 mm
- Simulate for: 1.5 hours.
Groundwater: 0 (off)
Calculation mode: Accuracy
Timeframes: 30
Output results: Surface last value, Surface last datum and Surface elevation
WEIR_DAM_MULTIPLIER is set to 3;
WEIR_MOVE_RANGE_M is set to 1 meter;
WEIR_MOVE_INTERVAL_S is set to 10 seconds;
WEIR_MOVE_STEP_M is set to 0,01 meter.

Output

Measured object graphs are displayed below. The following water overlay output attributes are inspected:

Object height, which is in meters relative to the datum
Object flow, which is in m3/s
Object datum a which is in meters relative to the datum
Object datum b which is in meters relative to the datum

Weir with constant height

Weir with a constant height:

Inlet:

Outlet:

Weir with manual configured changing height

Weir with a manual configured changing height:

Inlet:

Outlet:

Weir with adjusting height

Weir with an adjusting height:

Inlet:

Outlet:

Variations

Weir adjustment interval

Changing the WEIR_MOVE_INTERVAL_S from 10 seconds to 1 second. This leads to more adjustments. It becomes more apparent with more timeframes (300 in stead of 30).

Weir with an adjusting height:

Weir adjusting height with 300 frames:

Inlet: No changes.

Outlet:

Weir move step

Changing the WEIR_MOVE_INTERVAL_S from 0.01 meter to 0.05 meter. As you can see, this makes the adjustments more erratic.

Weir with an adjusting height:

Inlet: No changes.

Outlet:

Conclusions

Weirs can be made to adjust automatically based on changing water levels.
Be careful when changing the default values of the weir move attributes of the overlay. Do not set the adjustment time too low or the step too high.

How-to's

Water Module

Tutorials

Overview

Theory

Benchmarks

@@ Line 1: / Line 1: @@
-This page contains information how to inspect [[Weir (Water Overlay)|weir]] [[Object flow output (Water Overlay)|flow]] for [[Water Overlays]]. It also sets up a test case, which is described first.
+This page contains information on what ways a [[Weir height (Water Overlay)|weir's height]] can be configured using a test case. It also shows what direct output you can inspect from a  [[Weir (Water Overlay)|weir]]. Finally, several variants are also explored.
 ==Description==
@@ Line 6: / Line 6: @@
 ==Boundary and initial conditions==
-*''Waterways with weirs in the middle, separating two water areas.''
+*Waterways with weirs in the middle, separating two water areas.
-*''One inlet per waterway providing an influx of water, situated in the water area on the left.''
+*One inlet per waterway providing an influx of water, situated in the water area on the left.
-*''One outlet per waterway providing an outflux of water, situated in the water area on the right.''
+*One outlet per waterway providing an outflux of water, situated in the water area on the right.
 ==Parameter values==
@@ Line 32: / Line 32: @@
 ====Inlets====
-* Inlet (Constant):
+* [[Inlet (Water Overlay)|Inlet]] (Constant):
 ** Rectangle shape: [189.82, -254.350], [202.08, -251.510]
 ** [[Inlet area (Water Overlay)|INLET_AREA]] = 1.0;
@@ Line 40: / Line 40: @@
-* Inlet (Manual)
+* [[Inlet (Water Overlay)|Inlet]] (Manual)
 ** Rectangle shape:  [192.116, -331.225], [199.453, -328.390]
 ** [[Inlet area (Water Overlay)|INLET_AREA]] = 1.0;
@@ Line 47: / Line 47: @@
 ** [[Inlet upper threshold (Water Overlay)|UPPER_THRESHOLD]] = -10 000 (inactive);
-* Inlet (Adjusting)
+* [[Inlet (Water Overlay)|Inlet]] (Adjusting)
 [[File:Weir_flow_test_case_adjusting_inlet_q.png|thumb|200px|right|Inlet Q that is adjusting over time, visualized using the Measurement Tool's object attribute inspection.]]
 ** Rectangle shape:  [197.019, -444.276], [204.623, -441.738]
@@ Line 56: / Line 56: @@
 ====Outlets====
-Each outlet is set up with the following attributes to remove the water that passed through the weir:
+Each [[Inlet (Water Overlay)|outlet]]  is set up with the following attributes to remove the water that passed through the weir:
 ** [[Inlet area (Water Overlay)|INLET_AREA]] = 1.0;
 ** [[Inlet q (Water Overlay)|INLET_Q]] = 0;
@@ Line 70: / Line 70: @@
 ====Weirs====
-Each weir is setup using a rectangular shape, and direction angle and a weir height and width:
+Each [[Weir (Water Overlay)|weir]] is setup using a rectangular shape, and direction angle and a weir height and width:
 * [[Weir angle (Water Overlay)|WEIR_ANGLE]] = 270 degrees;
 * [[Weir height (Water Overlay)|WEIR_HEIGHT]] = 0 m;
@@ Line 81: / Line 81: @@
 [[File:Weir_flow_test_case_manuel_weir_height.png|thumb|200px|right|Weir height that is adjusting over time, visualized using the Measurement Tool's object attribute inspection.]]
 ** Rectangular shape: [ 298.675, -324.174 ] , [ 301.613, -335.662 ]
-* [[Weir height (Water Overlay)|WEIR_HEIGHT]] = [ 0 0 600 0.2 1200 0.2 1500 0.2 1800 -0.5 2400 -0.5 2700 0 ];
+** [[Weir height (Water Overlay)|WEIR_HEIGHT]] = [ 0 0 600 0.2 1200 0.2 1500 0.2 1800 -0.5 2400 -0.5 2700 0 ];
 * Weir (Adjusting)
 ** Rectangular shape: [ 298.406, -437.681 ] , [ 301.142, -449.731 ]
+** [[Weir target level (Water Overlay)|WEIR_TARGET_LEVEL]] = 0;
 ====Overlay settings====
@@ Line 94: / Line 95: @@
 * Groundwater: 0 (off)
 * Calculation mode: Accuracy
+* [[Timeframes (Water Overlay)|Timeframes]]: 30
 * Output results: [[Surface last value result type (Water Overlay)|Surface last value]], [[Surface last datum result type (Water Overlay)|Surface last datum]] and [[Surface last datum result type (Water Overlay)|Surface elevation]]
+* [[Weir dam multiplier (Water Overlay)|WEIR_DAM_MULTIPLIER]] is set to 3;
+* [[Weir move range m (Water Overlay)| WEIR_MOVE_RANGE_M]] is set to 1 meter;
+* [[Weir move interval s (Water Overlay)| WEIR_MOVE_INTERVAL_S]] is set to 10 seconds;
+* [[Weir move step m (Water Overlay)| WEIR_MOVE_STEP_M]] is set to 0,01 meter.
 ==Output==
-Measured object graphs are displayed below.
+Measured object graphs are displayed below. The following water overlay output attributes are inspected:
+* [[Object height output (Water Overlay)|Object height]], which is in meters relative to the {{datum}}
+* [[Object flow output (Water Overlay)|Object flow]], which is in m3/s
+* [[Object datum output a (Water Overlay)|Object datum a]] which is in meters relative to the {{datum}}
+* [[Object datum output b (Water Overlay)|Object datum b]] which is in meters relative to the {{datum}}
 ====Weir with constant height====
@@ Line 149: / Line 159: @@
 <li style = "display:inline-block">[[File:weir_test_case_outlet_adjusting_datum_b.png|x300px|border]]</li>
 </ul>
+==Variations==
+====Weir adjustment interval====
+Changing the [[Weir move interval s (Water Overlay)|WEIR_MOVE_INTERVAL_S]] from 10 seconds to 1 second. This leads to more adjustments. It becomes more apparent with more timeframes (300 in stead of 30).
+<ul>
+: Weir with an adjusting height:
+<li style = "display:inline-block">[[File:weir_test_case_weir_adjusting_height_1s.png|x300px|border]]</li>
+<li style = "display:inline-block">[[File:weir_test_case_weir_adjusting_flow_1s.png|x300px|border]]</li>
+<li style = "display:inline-block">[[File:weir_test_case_weir_adjusting_datum_a_1s.png|x300px|border]]</li>
+<li style = "display:inline-block">[[File:weir_test_case_weir_adjusting_datum_b_1s.png|x300px|border]]</li>
+: Weir adjusting height with 300 frames:
+<li style = "display:inline-block">[[File:weir_test_case_weir_adjusting_height_1s_0_01m_300f.png|x300px|border]]</li>
+<li style = "display:inline-block">[[File:weir_test_case_weir_adjusting_flow_1s_0_01m_300f.png|x300px|border]]</li>
+: Inlet: No changes.
+: Outlet:
+<li style = "display:inline-block">[[File:weir_test_case_outlet_adjusting_flow_1s.png|x300px|border]]</li>
+<li style = "display:inline-block">[[File:weir_test_case_outlet_adjusting_datum_a.png|x300px|border]]</li>
+<li style = "display:inline-block">[[File:weir_test_case_outlet_adjusting_datum_b.png|x300px|border]]</li>
+</ul>
+====Weir move step====
+Changing the [[Weir move interval s (Water Overlay)|WEIR_MOVE_INTERVAL_S]] from 0.01 meter to 0.05 meter. As you can see, this makes the adjustments more erratic.
+<ul>
+: Weir with an adjusting height:
+<li style = "display:inline-block">[[File:weir_test_case_weir_adjusting_height_0_05m.png|x300px|border]]</li>
+<li style = "display:inline-block">[[File:weir_test_case_weir_adjusting_flow_0_05m.png|x300px|border]]</li>
+<li style = "display:inline-block">[[File:weir_test_case_weir_adjusting_datum_a_0_05m.png|x300px|border]]</li>
+<li style = "display:inline-block">[[File:weir_test_case_weir_adjusting_datum_b_0_05m.png|x300px|border]]</li>
+: Inlet: No changes.
+: Outlet:
+<li style = "display:inline-block">[[File:weir_test_case_outlet_adjusting_flow_0_05m.png|x300px|border]]</li>
+<li style = "display:inline-block">[[File:weir_test_case_outlet_adjusting_datum_a.png|x300px|border]]</li>
+<li style = "display:inline-block">[[File:weir_test_case_outlet_adjusting_datum_b.png|x300px|border]]</li>
+</ul>
+==Conclusions==
+* Weirs can be made to adjust automatically based on changing water levels.
+* Be careful when changing the default values of the weir move attributes of the overlay. Do not set the adjustment time too low or the step too high.
 {{article end
 |howtos=
-* [[How to inspect object output attributes of an overlay using the measurement tool.]]
+* [[How to inspect object output attributes of an overlay using the measurement tool]]
+* [[How to import a time sequence with a CSV]]
 }}
 [[Category:Benchmarks]]
 {{Water Module buttons}}

Weir height test case (Water Module): Difference between revisions

Latest revision as of 12:53, 3 February 2023

Contents

Description

Boundary and initial conditions

Parameter values