How to configure the Waterwijzer Overlay to use groundwater results from other calculations: Difference between revisions

From Tygron Support wiki
Jump to navigation Jump to search
mNo edit summary
No edit summary
 
(3 intermediate revisions by 2 users not shown)
Line 1: Line 1:
The [[Waterwijzer Overlay]] can provide insight into the loss of earnings in agrarian locations, due to hydrological conditions in the underground. By connecting it to other calculation models, specifically for their computed groundwater levels, it's possible to set up a dynamic model in which actions can directly influence the viability of crops, and thus the resulting expected earnings.
The [[Waterwijzer Overlay]] can provide insight into the yield loss in agrarian locations, due to hydrological conditions in the underground. By connecting it to other calculation models, specifically for their computed groundwater levels, it's possible to set up a dynamic model in which actions can directly influence the viability of crops, and thus the resulting expected yields.


==Adding subsidence calculations==
==Adding subsidence calculations==
To account for subsidence, and its effects on groundwater when using the [[Waterwijzer Overlay]], make sure:
* The project has a configured [[Subsidence Overlay]].
* The [[Subsidence Overlay]] has both a [[Hi ground water result type (Subsidence Overlay)|high ground water]] result type and a [[Low ground water result type (Subsidence Overlay)|low ground water]] result type.


{{editor location|Overlay|Waterwijzer Overlay}}
{{editor location|Overlay|Waterwijzer Overlay}}


{{howto|title=account for subsidence in the Waterwijzer Overlay|
{{howto|title=account for subsidence in the Waterwijzer Overlay|
| Ensure the project has a configured [[Subsidence Overlay]].
| Ensure the [[Subsidence Overlay]] has both a [[Hi ground water result type (Subsidence Overlay)|high ground water]] result type and a [[Low ground water result type (Subsidence Overlay)|low ground water]] result type.
| In the [[Editor]], open the list of [[Overlay]]s.
| In the [[Editor]], open the list of [[Overlay]]s.
| In the [[left panel]], select the [[Waterwijzer Overlay]], and open its configuration wizard.
| In the [[left panel]], select the [[Waterwijzer Overlay]], and open its configuration wizard.
Line 16: Line 17:
| Select the [[Subsidence Overlay]]'s result for [[Hi ground water result type (Subsidence Overlay)|high ground water]].
| Select the [[Subsidence Overlay]]'s result for [[Hi ground water result type (Subsidence Overlay)|high ground water]].
| Finish and close the wizard.
| Finish and close the wizard.
| If neccesary, [[recalculate]] the [[Overlay]].
| If necessary, [[recalculate]] the [[Overlay]].
| The [[Waterwijzer Overlay]] now shows results.
| The [[Waterwijzer Overlay]] now shows new results.
}}
}}


==Using groundwater calculations==
==Using groundwater calculations==
To account for dynamically calculated groundwater flow when using the [[Waterwijzer Overlay]], make sure:
* The project has a configured [[Water Overlay]].
* The [[Water Overlay]] is set to [[Ground water (Water Overlay)|fully simulate groundwater flow]]
* The [[Water Overlay]] has a [[Ground watertable result type (Water Overlay)|ground watertable]] result type.


==Notes==
{{editor location|Overlay|Waterwijzer Overlay}}
 
{{howto|title=dynamically calculate groundwater for the Waterwijzer Overlay|
| In the [[Editor]], open the list of [[Overlay]]s.
| In the [[left panel]], select the [[Waterwijzer Overlay]], and open its configuration wizard.
| Continue to the groundwater steps.
| In the step for low groundwater, opt to select an Overlay.
| Select the [[Water Overlay]]'s result for [[Ground watertable result type (Water Overlay)|ground watertable]].
| In the step for high groundwater, opt to select an Overlay.
| Select the [[Water Overlay]]'s result for [[Ground watertable result type (Water Overlay)|ground watertable]].
| Finish and close the wizard.
| If necessary, [[recalculate]] the [[Overlay]].
| The [[Waterwijzer Overlay]] now shows new results.
}}
 
{{article end
|notes=
* To add both subsidence and groundwater flow calculations, first [[How to add Subsidence (Water Overlay)|add subsidence to the Water Overlay]], and then follow the steps for connecting the results of the [[Water Overlay]] to the [[Waterwijzer Overlay]].
* To add both subsidence and groundwater flow calculations, first [[How to add Subsidence (Water Overlay)|add subsidence to the Water Overlay]], and then follow the steps for connecting the results of the [[Water Overlay]] to the [[Waterwijzer Overlay]].


==See also==
|howtos=
* [[How to add the Waterwijzer Overlay]]
* [[How to add the Waterwijzer Overlay]]
}}
[[Category:How-to's]]

Latest revision as of 13:35, 30 January 2024

The Waterwijzer Overlay can provide insight into the yield loss in agrarian locations, due to hydrological conditions in the underground. By connecting it to other calculation models, specifically for their computed groundwater levels, it's possible to set up a dynamic model in which actions can directly influence the viability of crops, and thus the resulting expected yields.

Adding subsidence calculations

To account for subsidence, and its effects on groundwater when using the Waterwijzer Overlay, make sure:

Editor → Current Situation (Ribbon tab) → Overlays (Ribbon bar) → Waterwijzer Overlay (Left panel)
How to account for subsidence in the Waterwijzer Overlay:
  1. In the Editor, open the list of Overlays.
  2. In the left panel, select the Waterwijzer Overlay, and open its configuration wizard.
  3. Continue to the groundwater steps.
  4. In the step for low groundwater, opt to select an Overlay.
  5. Select the Subsidence Overlay's result for low ground water.
  6. In the step for high groundwater, opt to select an Overlay.
  7. Select the Subsidence Overlay's result for high ground water.
  8. Finish and close the wizard.
  9. If necessary, recalculate the Overlay.
  10. The Waterwijzer Overlay now shows new results.

Using groundwater calculations

To account for dynamically calculated groundwater flow when using the Waterwijzer Overlay, make sure:

Editor → Current Situation (Ribbon tab) → Overlays (Ribbon bar) → Waterwijzer Overlay (Left panel)
How to dynamically calculate groundwater for the Waterwijzer Overlay:
  1. In the Editor, open the list of Overlays.
  2. In the left panel, select the Waterwijzer Overlay, and open its configuration wizard.
  3. Continue to the groundwater steps.
  4. In the step for low groundwater, opt to select an Overlay.
  5. Select the Water Overlay's result for ground watertable.
  6. In the step for high groundwater, opt to select an Overlay.
  7. Select the Water Overlay's result for ground watertable.
  8. Finish and close the wizard.
  9. If necessary, recalculate the Overlay.
  10. The Waterwijzer Overlay now shows new results.

Notes

How-to's

Retrieved from "https://support.tygron.com/w/index.php?title=How_to_configure_the_Waterwijzer_Overlay_to_use_groundwater_results_from_other_calculations&oldid=58197"