Search results

• Vegetation fraction (Heat Overlay)
  * [[Foliage height calculation model (Heat Overlay)|Foliage Height calculation]] {{HeatOverlay model attribute nav}}
  1 KB (165 words) - 12:08, 22 September 2023
• Wind speed (Heat Overlay)
  * [[Wind calculation model (Heat Overlay)]] {{HeatOverlay model attribute nav}}
  618 bytes (81 words) - 14:43, 15 March 2024
• Limitation area (Water Overlay)
  ...to restrict its calculations to specific locations. When the [[limit area model attribute (Water Overlay)|LIMIT_AREA]] Attribute of the Overlay is set to t ...iate value. Otherwise, the Limitation areas do not affect any facet of the calculation.
  876 bytes (126 words) - 08:12, 27 April 2021
• Traffic Density Overlay
  {{main|Model attributes (Traffic Density Overlay)}} ...calculation is then defined by the [[Hours (Traffic Density Overlay)|HOURS model Attribute]].
  3 KB (397 words) - 15:54, 15 December 2023
• How to correct a building at the edge of the project area
  ...|300px|thumb|right|The Weir removed, as it would have had no effect on the model.]] ...of the [[limit area (Water Overlay)|calculation area]], or being [[border model (Water Overlay)|too close to the edge of the project area]].
  2 KB (348 words) - 13:42, 30 January 2024
• How to generate an initialized groundwater situation
  When working with the [[Ground model (Water Overlay)|complete groundwater model]] of the [[Water Overlay]], it is very likely that any initial configuratio ...natural and stable) result as the initial groundwater state for the actual calculation.
  4 KB (582 words) - 15:03, 30 January 2024
• Overlay Key
  ...establish a link between [[Attributes]] that an [[Overlay]]'s calculation model requires and [[Attributes]] the users and geo-sources supply. The Keys an Overlay's calculation model uses and their configured values can be found under the tab Keys in the [[r
  2 KB (395 words) - 16:36, 18 October 2019
• Timeframes (Water Overlay)
  |description=The number of intermediate results recorded during the calculation. Each [[timeframe]] becomes a snapshot of data which can be viewed and anal * The amount of timeframes does not impact the calculation time or the simulation time.
  880 bytes (122 words) - 15:05, 26 January 2024
• Subsidence calculation
  The subsidence model calculates the gradual downward settling of the ground's surface where a pe The calculation model is configured by the subsidence overlay wizard and it's result are visualiz
  5 KB (723 words) - 14:10, 28 February 2024
• Terrain (Subsidence Overlay)
  ...by an underground terrain, and therefore each grid cell of the subsidence model can be given default values for the subsidence keys listed below. The subsi
  758 bytes (100 words) - 13:09, 1 April 2021
• Exclude buildings (Heat Overlay)
  ...about the effect that higher (green) walls and roofs may have on the DPRA model. ...he buildings as part of the elevation model, and as such a the heat stress calculation is performed also on the buildings.
  1 KB (215 words) - 15:01, 15 March 2024
• Sun altitude (Heat Overlay)
  * [[Shade calculation model (Heat Overlay)]]. {{HeatOverlay model attribute nav}}
  853 bytes (110 words) - 14:44, 15 March 2024
• How to investigate increasing water levels in waterways
  ...ionary calculations, you would expect the amount of water flowing into the model to roughly balance the amount of water being removed from the water as well ...zard|configuration wizard]], where the total amount of rainfall during the calculation is listed.
  5 KB (757 words) - 15:31, 30 January 2024
• Maplink
  |CALCULATION |CALCULATION
  4 KB (517 words) - 11:17, 5 March 2024
• How to investigate odd behavior near model edges
  ...should, for the most part, be able to flow naturally. However, as with any model, at some point the [[Water Overlay]] has an edge, leading to partially unex ...in the configuration wizard, where you can check the configuration for the calculation area. If it is set to Water Areas only, check whether the location of the i
  2 KB (345 words) - 15:31, 30 January 2024
• Sun azimuth (Heat Overlay)
  * [[Shade calculation model (Heat Overlay)]] {{HeatOverlay model attribute nav}}
  867 bytes (117 words) - 14:44, 15 March 2024
• Climate oxidation (Subsidence Overlay)
  ...The oxidation factor used to recalculate the climate values between 1-year calculation steps. {{SubsidenceOverlay model attribute nav}}
  522 bytes (59 words) - 13:13, 10 February 2021
• Climate soil temp factor (Subsidence Overlay)
  ...l temperature factor used to recalculate the climate values between 1-year calculation steps. {{SubsidenceOverlay model attribute nav}}
  537 bytes (63 words) - 13:13, 10 February 2021
• A (Subsidence Overlay)
  |notes=This value is recalculated between 1-year time steps of the calculation. {{SubsidenceOverlay model attribute nav}}
  598 bytes (70 words) - 15:28, 10 February 2021
• Route bicycles (Travel Distance Overlay)
  |description= Whether roads with bicycle traffic should be included in the calculation or not. ...attribute, roads with bicycle traffic are included in the travel distance model. Select 0 to ignore roads with bicycle traffic.
  527 bytes (68 words) - 12:14, 24 February 2022

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)