UK Benchmark 1 (Water Module): Difference between revisions

From Tygron Support wiki
Jump to navigation Jump to search
Line 38: Line 38:
Measured point graphs are displayed below:
Measured point graphs are displayed below:
<ul>
<ul>
<li style = "display:inline-block">[[File:graph_p1_case1_ukbm.png|x400px|right|border]]</li>
<li style = "display:inline-block">[[File:graph_p1_case1_ukbm.png|x400px|border]]</li>
<li style = "display:inline-block">[[File:graph_others_p1_case1_ukbm.png|x400px|right|border]]</li>
<li style = "display:inline-block">[[File:graph_others_p1_case1_ukbm.png|x400px|border]]</li>
: Graph of point 1 generated by {{software}} on the left and generated by others on the right.
: Graph of point 1 generated by the {{software}} on the left and generated by others on the right.
<li style = "display:inline-block">[[File:graph_p2_case1_ukbm.png|x400px|right|border|Graph of point 2]]</li>
<li style = "display:inline-block">[[File:graph_p2_case1_ukbm.png|x400px|border]]</li>
<li style = "display:inline-block">[[File:graph_others_p2_case1_ukbm.png|x400px|right|border|Graph of other packages for point 2]]</li>
<li style = "display:inline-block">[[File:graph_others_p2_case1_ukbm.png|x400px|border]]</li>
: Graph of point 1 generated by {{software}} on the left and generated by others on the right.
: Graph of point 1 generated by the {{software}} on the left and generated by others on the right.
<li style = "display:inline-block">[[File:graph_xslice_case1_ukbm.png|x800px|border]]</li>
: Slice of the situation in the x -direction, generated by the {{software}}.
</ul>
</ul>


==Notes==  
==Notes==  
* Tests are run with multi gpu setup. For small cases like this, running it on a single gpu is actually faster: 17 seconds, which is +- 40% compared to 2.
* Tests are run with multi gpu setup. For small cases like this, running it on a single gpu is actually faster: 17 seconds, which is +- 40% compared to 2.

Revision as of 12:10, 17 April 2019

This page contains the test case 1 of the UK benchmark named Test 1 – Uncovering of a beach as well as its result generated by the Water Module in the Tygron Platform.

This test consists of a sloping topography with a depression. An inflow boundary condition is applied at the low end, causing the water to rise to the level indicated by a thick blue line. The inflow is then replaced by a sink term until the water level becomes as indicated by the thin blue line. A similar test has been used by EDF (2000) for validation of the TELEMAC package. The aim of the test is to assess basic package capabilities such as handling disconnected water bodies and wetting and drying of floodplains.

Description

Fig. a: Sloping topography with depression

This test consists of a sloping topography with a depression as illustrated in Figure (a). The modeled domain is a perfect 700m x 100m rectangle. A varying water level, see Figure (b), is applied as a boundary condition along the entire length of the left-hand side of the rectangle, causing the water to rise to level 10.35m. This elevation is maintained for long enough for the water to fill the depression and become horizontal over the entire domain. It is then lowered back to its initial state, causing the water level in the pond to become horizontal at the same elevation as the sill, 10.25m.

Fig. b: Top down situation
Fig. c: Water level rise at the left boundary


Boundary and initial conditions

Varying water level along the dashed red line in Figure (a). Table provided as part of dataset. All other boundaries are closed.
Initial condition: Water level elevation = 9.7m.

Parameter values

  • Manning’s n: 0.03 (uniform)
  • Model grid resolution: 10m (or 700 nodes in the area modelled)
  • Time of end: the model is to be run until time t = 20 hours

Technical setup

The provided ascii height file named test1DEM.asc is first imported. It has a cell size of 2m, while the test is expected to run on a 10m grid. Therefore, it will be automatically rescaled by the grid rasterizer. The resulting rescaled asc file is packed in the down below.

Output as required

  • Software package used: Tygron Platform
  • Numerical scheme: FV (Kurganov, Bollerman, Horvath)*
  • Specification of hardware used to undertake the simulation:
    • Processor: Intel Xeon @2.10GHz x 8,
    • RAM 62.8 GiB,
    • GPU: 2x NVidia 1080
    • Operating system: Linux 4.13
  • Time increment used: adaptive: 0.25 - 1.13 s.
  • Grid resolution: 10 m.
  • Simulation time: 28s.
  • Remaining volume water: 18672 m3

Measured point graphs are displayed below:

  • Graph p1 case1 ukbm.png
  • Graph others p1 case1 ukbm.png
  • Graph of point 1 generated by the Tygron Platform on the left and generated by others on the right.
  • Graph p2 case1 ukbm.png
  • Graph others p2 case1 ukbm.png
  • Graph of point 1 generated by the Tygron Platform on the left and generated by others on the right.
  • Graph xslice case1 ukbm.png
  • Slice of the situation in the x -direction, generated by the Tygron Platform.

Notes

  • Tests are run with multi gpu setup. For small cases like this, running it on a single gpu is actually faster: 17 seconds, which is +- 40% compared to 2.