Water Overlay Wizard: Difference between revisions

From Tygron Support wiki
Jump to navigation Jump to search
Line 18: Line 18:
: '''Ground water''': [[Underground model (Water Overlay)|Ground water]], the height of the underground saturated by water relative to {{datum}}. A [[Geotiff (Overlay)|GeoTIFF]] can be [[Geo Data Wizard|imported]].
: '''Ground water''': [[Underground model (Water Overlay)|Ground water]], the height of the underground saturated by water relative to {{datum}}. A [[Geotiff (Overlay)|GeoTIFF]] can be [[Geo Data Wizard|imported]].
: '''Sewers''': [[Sewer area (Water Overlay)|Sewer areas]], the broad definitions for where what kind of sewers exist. It is also possible to have the wizard generate sewer areas based on the [[neighborhood]]s in the project area.
: '''Sewers''': [[Sewer area (Water Overlay)|Sewer areas]], the broad definitions for where what kind of sewers exist. It is also possible to have the wizard generate sewer areas based on the [[neighborhood]]s in the project area.
: '''Inundation areas''': {{inlink|Inundation|Inundation area}}s, definitions of water on the surface, in the form of inundated land. It is also possible to have the wizard generate a single inundation area covering the entire project area.
: '''Inundation areas''': [[Inundation area (Water Overlay)|Inundation areas]], definitions of water on the surface, in the form of inundated land. It is also possible to have the wizard generate a single inundation area covering the entire project area.
: '''Aquifer areas''' ([[Groundwater_(Overlay)|groundwater overlays]] only): {{inlink|Aquifer|Aquifer area}}s, definitions for transmissivity or hydraulic conductivity of the underground layer.
: '''Aquifer areas''' ([[Groundwater_(Overlay)|groundwater overlays]] only): [[Aquifer (Water Overlay)|Aquifer areas]], definitions for transmissivity or hydraulic conductivity of the underground layer.


: '''Weirs''': {{inlink|Weir}}s, minor barriers in the water flow.
: '''Weirs''': [[Weir (Water Overlay)|Weirs]], minor barriers in the water flow.
: '''Culverts''': {{inlink|Culvert}}s, tunnels which form direct connections between two locations.
: '''Culverts''': Culvert (Water Overlay)|Culverts]], tunnels which form direct connections between two locations.
: '''Pumps''': {{inlink|Pump}}s, structures which move water from a lower to a higher location.
: '''Pumps''': [[Pump (Water Overlay)|Pumps]], structures which move water from a lower to a higher location.
: '''Inlets''': {{inlink|Inlet}}s, structures which add or remove water.
: '''Inlets''': {{inlink|Inlet}}s, structures which add or remove water.
: '''Sewer overflows''': {{inlink|Sewer overflow}}s, points where water from sewers can flow back onto the surface.
: '''Sewer overflows''': {{inlink|Sewer overflow}}s, points where water from sewers can flow back onto the surface.

Revision as of 12:14, 12 April 2019

Flooding Wizard Introduction Page

The configuration wizard is a special interface which helps to guide the configuration of the overlay. Across multiple steps, it progresses through each type of Data which can be configured, along with the most important attributes of the overlay.

Template:Editor ribbon

Each of the water overlay variants has a configuration wizard which helps the user with configuring the overlay. The general structure of the wizard is the same for all variants, with the exception that for flooding overlays a step for configuring a breach area is included as well.

When the wizard has been completed once, it can be reopened at any time, and any step can be accessed anew.

Step 1: Weather

Step 1: Weather event

The weather event defines the total simulation time and the weather and climate effects during the simulation. Specifically, the amount of rain and when it falls during the simulation, as well as the evaporation which takes place.

Step 2: Water system

Step 2: Setup Water System

The water system is the most complex step of the configuration and contains a multitude of substeps to configure all geographical data. Its various components can be configured in the following order:

Breach (flooding overlays only): A breach area, a location where an (uncontrolled) inflow of water takes places.
Water areas: Water level areas, defined regions in which a specific water level is maintained. It is also possible to have the wizard generate a single water level area for the entire project area.
Ground water: Ground water, the height of the underground saturated by water relative to datum. A GeoTIFF can be imported.
Sewers: Sewer areas, the broad definitions for where what kind of sewers exist. It is also possible to have the wizard generate sewer areas based on the neighborhoods in the project area.
Inundation areas: Inundation areas, definitions of water on the surface, in the form of inundated land. It is also possible to have the wizard generate a single inundation area covering the entire project area.
Aquifer areas (groundwater overlays only): Aquifer areas, definitions for transmissivity or hydraulic conductivity of the underground layer.
Weirs: Weirs, minor barriers in the water flow.
Culverts: Culvert (Water Overlay)|Culverts]], tunnels which form direct connections between two locations.
Pumps: Pumps, structures which move water from a lower to a higher location.
Inlets: Inlets, structures which add or remove water.
Sewer overflows: Sewer overflows, points where water from sewers can flow back onto the surface.

All of the above components can be imported or connected to the hydrological model.


Step 3: Hydrological coefficients

Step 3: Hydrological coefficients

Hydrological coefficients are values of existing elements of the world, specifically terrain and constructions. The coefficients dictate the ability of water to flow between cells and layers. The following data can be configured:

Surface terrain: For the surface terrains, attributes can be adjusted directly.
Underground terrain: For the underground terrains, attributes can be adjusted directly as well.
Constructions: For constructions, the wizard links to the function values editing screen, and will open it the "WATER" filter for the values to display.


Step 4: Interaction

Step 4: Interaction

The wizard provides a few options to automatically generate methods of interaction with the hydrological model. The system visualization can be activated or deactivated. Additionally, for some hydrological constructions and features panels can be generated which allow for their most important attributes during a session.

Step 5: Output overlays

Step 5: Output overlays

Multiple result types are available. In the wizard multiple result types can be selected. One result type (indicated with the "First" checkbox) will be the main overlay's result type. The other selections will become result child overlays. Relevant attributes can be modified as well, if they are related to selected result types.

Finally, the TIMEFRAMES attribute can be configured here as well, defining the amount of result snapshots which should be made during the calculation.

Step 6: Input overlays

Step 5: Input overlays

To gain more insight into the data used by the model, you may opt to add one or more input overlays as well. These add Average Overlays configured for the geographical display of attribute values relevant for the calculation of the water model.