Water Overlay

What are the Water Overlays

With the Water Overlays the following overlays are meant:

• Rainfall Overlay
• Flooding Overlay
• Groundwater Overlay

Each of these overlays have some common configuration steps which will be described on this page.

Configuration Wizard

Each of the Water Overlays have a configuration wizard which helps the user with configuring the overlay. The Configuration Wizard can be found in the General tab of the overlay. For the Flooding Overlay the wizard has an extra step, the Rainfall and Groundwater wizard are basically the same.

Result types

Each Water Overlay is a grid overlay showing results on the surface (flooding), sub-surface (groundwater), open water and sewer system. The following results are produced:

Result type	Unit	Description
BASE_TYPES	nominal value	Division of gridcells in water, land or sewer areas that are connected to the sewer.
CHLORIDE		Initial groundwater level relative to the surface level (NL: ontwateringsdiepte).
EVAPORATED	m (mm)¹	Total evaporation over the simulation period
GPU OVERVIEW		Initial groundwater level relative to the surface level (NL: ontwateringsdiepte).
IMPACTED_BUILDINGS	nominal value	Constructions impacted by flood: the value from the function value indicator is assigned to a building if the water depth at a grid-cell surrounding the building exceeds the overlay attribute value IMPACT_FLOOD_TRESHOLD_M
LAST SPEED		Initial groundwater level relative to the surface level (NL: ontwateringsdiepte).
MAX SPEED	m (below surface)	Initial groundwater level relative to the surface level (NL: ontwateringsdiepte).
NITROGEN	m (below surface)	Initial groundwater level relative to the surface level (NL: ontwateringsdiepte).
PHOSPHORUS	m (below surface)	Initial groundwater level relative to the surface level (NL: ontwateringsdiepte).
SEWER_LAST_VALUE	m (mm)¹	The amount of water in the sewer storage at the end of simulation
SEWER_MAX_VALUE	m (mm)¹	Maximum amount of water in the sewer storage during the simulation
SURFACE_DURATION	s (min)¹	The amount of time the water depth in a cell exceeds the value set in the overlay attribute value SHOW_DURATION_FLOOD_LEVEL_M
SURFACE_FLOW	m3/m2	Total volume of water passed a grid-cell, scaled by the cell surface (grid cell-size^2)
SURFACE_LAST_VALUE	m (min)¹	Water depth at the end of simulation
SURFACE_MAX_VALUE	m (min)¹	Maximum water depth during the simulation
UNDERGROUND_FLOW	m³/m²	Totall infiltration amount from the surface to groundwater
UNDERGROUND_LAST_STORAGE	m (mm)	The amount by which the groundwater table has risen above the initial groundwater level at the end of simulation
UNDERGROUND_LAST_VALUE	m (mm)	The amount by which the groundwater table has risen above the initial groundwater level at the end of simulation
UNDERGROUND_MAX_STORAGE	m (mm)	The amount by which the groundwater table has risen above the initial groundwater level at the end of simulation
UNDERGROUND_MAX_VALUE	m (mm)	The maximum amount by which the groundwater table has risen above the initial groundwater during the simulation
UNDERGROUND WATERTABLE	m (mm)	The Maximum water depth during the simulation. At water cells only a water depth is shown if the depth exceeds the overlay attribute value ALLOWED_WATER_INCREASE_M
WATER_STRESS	m (mm)	The Maximum water depth during the simulation. At water cells only a water depth is shown if the depth exceeds the overlay attribute value ALLOWED_WATER_INCREASE_M

¹ the units between () are as displayed in the 3D client. If exported to GTiff the SI-convention is used: meters (m) and seconds (s).

General Tab

The General Tab can be found at the panel on the right side, when selecting a Water Overlay. In this tab several settings can be adjusted.

1. Calculation Preference

Here you can manipulate the computation time step by choosing between the option SPEED, AVERAGE and ACCURACY. The computational timesteps will be set according to the Courant criterion:

Δt = Δx /u_max

where:

• Δt = computational timestep
• Δx = grid cell size
• u_max = max velocity, assumed 2.5 (SPEED), 5 (AVERAGE) and 10 (ACCURACY) m&sub3;/s respectively

2. Grid cell size

The Tygron Platform computes flow equations over a rectangular cartesian grid, the grid cell size can be set by cliking on Change Grid. Note: if you choose a smaller grid cell size, both the amount of time steps (see Calculation Preference) and amount of computational cells increase.

3. Refresh Grid

By Refreshing the grid, the Overlay is recalculated. This may take some time, depending on the grid cell size, the size of your project and the calcualtion preference.

4. Export Grid File

You can export the current result type as either a GeoTiff or ASCII file. Also, it is possible to export the difference result type of the current and maquette situation.

5. Save Overlay result

With this option you can create a duplicate inactive copy of the current overlay. This is noticeable in the Overlays panel on the left side of the screen. The duplicated overlay will have (inactive copy) behind the overlay name and is greyed out. This copy is not being recalculated when changing settings in the original duplicated overlay. When checking the checkbox: active in simulation, the copy becomes active again and can be recalculated. Also the overlay name is again in black and not grayed out anymore.

6. Show Water Balance

The Water Balance panel shows the in- and outflow of water in m3. The Water Balance panel is also visible when clicking on the Debug info (see below). The water balance is made up of the following components (dependent on what is in the project):

• Land surface: amount of water on the land surface after simulation (m3)
• Water surface: amount of water stored on water cells after simulation (m3)
• Building storage: amount of water stored in building storage (m3)
• Sewer storage: amount of water stored in sewers after simulation (m3)
• Underground storage: amount of water stored in the sub-soil after simulation (m3)
• Evaporated: amount of water evaporated after simulation (m3)
• Outlet: amount of water extracted from the model during the simulation via outlets of water areas or sewer pumps (m3).

7. Warnings

When the grid cell size is too large in combination with the project size, a warning pops up. This means that calculated results are not accurate. The solution to this is to change the grid cell size to a smaller number.

8. Debug Info

The debug info contains the following information:

• Rain: the amount of rainfall (mm) in the duration of the rainfall event (hours)
• Total Simulation: the simulation period (hours)
• Cells: The dimensions of the simulation: the amount of computational cells and the amount of time steps (cycles)
• Water areas:
• Weir flow: the amount of water flown over weirs during simulation (m3)
• Sewer overflow: the amount of water flown over sewer overflows during simulation (m3)
• GPU time: the computation time on GPU (seconds)
• Volume: total volume of the in- and outflow of water in the model.

Keys

The tab Keys refers to the settings for the water system (areas and constructions) that are adjusted by following the configuration wizard in the General tab. It is therefore generally not needed to change the keys in this tab, as this can be done also in the configuration wizard. However, below an explanation of the Overlay Keys.

Attribute	Unit	Description
Water Level	m + datum	initial water level, relative to datum, for all water cells in a water area
Outlet	m3/s	water abstraction for all water cells in a water area
Outlet level	m + datum	initial water level, relative to datum, for all water cells in a water area
Outlet capacity	m + datum	initial water level, relative to datum, for all water cells in a water area
Sewer Storage	m	available storage in sewers at the start of simulation in a sewer area
Sewer Pump Speed	m3/s	sewer water abstraction for all cells in a sewer area

Keys referring to structures (building attributes)

Attribute	Unit	Description
Weir Height	m + datum	weir crest level
Weir Output	m	the width of the crest of a weir
Weir Width	m	the width of the crest of a weir
Weir Coefficient		linear weir coefficient for accounting discharge & contraction losses
Culvert Speed	m3/s	the discharge capacity of a culvert
Pump Speed	m3/s	the capacity of a pump
Sewer Overflow Height	m + datum	the height of a crest of a sewer overflow
Sewer Overflow Speed	m3/s	the discharge capacity of a sewer overflow

Attributes

This tab shows the attributes of result types that can be adjusted. These attributes can also be adjusted in the configuration wizard in step 5 in the General tab. It is therefore generally not needed to change the attributes here. However, below an overview of the Overlay Attributes.

Attribute	Unit	Description
ALLOWED_WATER_INCREASE_M	m	increment by which the water level on a water cell is allowed to increase before the depth is shown in the water stress result type
IMPACT FLOOD_THRESHOLD_M	m	maximum waterdepth around a building where after the building is assumed impacted
MIN_SLOPE		slope whereunder the pressure slope is assumed 0
SEWER_OVERFLOW_THRESHOLD		fraction of storage whereafter sewer overflows take place
SIMULATION_TIME_HOURS	hours	simulation time