Inlet area (Water Overlay) - Revision history

Frank@tygron.nl at 11:08, 8 November 2024

2024-11-08T11:08:14Z

← Older revision		Revision as of 11:08, 8 November 2024
Line 12:		Line 12:
	* Selecting this option is useful when the [[Inlet q (Water Overlay)\|INLET_Q]] value is too large for a single cell.		* Selecting this option is useful when the [[Inlet q (Water Overlay)\|INLET_Q]] value is too large for a single cell.
	* The area works best when applied as a narrow strip.		* The area works best when applied as a narrow strip.
			* An inlet area always has one associated datum height. The selected height is the highest of all cells belonging to this area.
			** When using outlets to remove water on sloped terrain, using this setting can lead to the issue that not all water is removed. See the image below. It is therefor advised to disable this option and use center point outlets to remove water at the edge of your project.
	\|seealso=		\|seealso=
	\|howtos=		\|howtos=

Frank@tygron.nl at 09:41, 26 April 2021

2021-04-26T09:41:48Z

← Older revision		Revision as of 09:41, 26 April 2021
Line 3:		Line 3:
	\|key=INLET_AREA		\|key=INLET_AREA
	\|unit={{boolean}}		\|unit={{boolean}}
	\|description=When true the ~~inlet~~ is spread across the entire building surface.		\|description=When true the {{Inlet}} is spread across the entire building surface.
	\|defaultvalue=0		\|defaultvalue=0
	\|icon=waterwizard_icon_inlet_area.png		\|icon=waterwizard_icon_inlet_area.png

Rudolf@tygron.nl at 12:20, 2 October 2020

2020-10-02T12:20:50Z

← Older revision		Revision as of 12:20, 2 October 2020
Line 1:		Line 1:
	{{Overlay ~~attribute~~		{{Overlay keys\|<onlyinclude>
	\|key=~~[[Inlet_area_(Water_Overlay)\|~~INLET_AREA]]		{{Overlay keys\|type=row\|group=Water Overlay
			\|key=INLET_AREA
	\|unit={{boolean}}		\|unit={{boolean}}
	\|description=When true the inlet is spread across the entire building surface.		\|description=When true the inlet is spread across the entire building surface.
	\|defaultvalue=0		\|defaultvalue=0
	\|icon=~~[[File:~~waterwizard_icon_inlet_area.png]]		\|icon=waterwizard_icon_inlet_area.png
			}}</onlyinclude>}}

			{{article end
			\|notes=
			* Selecting this option is useful when the [[Inlet q (Water Overlay)\|INLET_Q]] value is too large for a single cell.
			* The area works best when applied as a narrow strip.
			\|seealso=
			\|howtos=
	}}		}}
	~~==Notes==~~
	* Selecting this option is useful when the Inlet Q amount is too large for a single cell.
	* The area works best when applied as a narrow strip.

	{{WaterOverlay hydraulic structure nav}}		{{WaterOverlay hydraulic structure nav}}

Rudolf@tygron.nl at 07:02, 15 June 2020

2020-06-15T07:02:49Z

← Older revision		Revision as of 07:02, 15 June 2020
Line 1:		Line 1:
	{{Overlay attribute		{{Overlay attribute
	\|key=[[Inlet_area_(Water_Overlay)\|INLET_AREA]]		\|key=[[Inlet_area_(Water_Overlay)\|INLET_AREA]]
	\|unit=~~bool~~		\|unit={{boolean}}
	\|description=When true the inlet is spread across the entire building surface.		\|description=When true the inlet is spread across the entire building surface.
	\|defaultvalue=0		\|defaultvalue=0

Frank@tygron.nl at 11:28, 8 May 2020

2020-05-08T11:28:14Z

← Older revision		Revision as of 11:28, 8 May 2020
Line 1:		Line 1:
	{{Overlay attribute		{{Overlay attribute
	\|key=[[Inlet_area_(Water_Overlay)\|INLET_AREA]]		\|key=[[Inlet_area_(Water_Overlay)\|INLET_AREA]]
	\|unit=m3		\|unit=bool
	\|description=When true the inlet is spread across the entire building surface.		\|description=When true the inlet is spread across the entire building surface.
	\|defaultvalue=0		\|defaultvalue=0

Frank@tygron.nl: Created page with "{{Overlay attribute |key=INLET_AREA |unit=m3 |description=When true the inlet is spread across the entire building surface. |defaultvalue=0 |ico..."

2020-05-08T11:17:57Z

Created page with "{{Overlay attribute |key=INLET_AREA |unit=m3 |description=When true the inlet is spread across the entire building surface. |defaultvalue=0 |ico..."

New page

{{Overlay attribute
|key=[[Inlet_area_(Water_Overlay)|INLET_AREA]]
|unit=m3
|description=When true the inlet is spread across the entire building surface.
|defaultvalue=0
|icon=[[File:waterwizard_icon_inlet_area.png]]
}}
==Notes==
* Selecting this option is useful when the Inlet Q amount is too large for a single cell.
* The area works best when applied as a narrow strip.

{{WaterOverlay hydraulic structure nav}}